Church Scan / Guide

How to make an evacuation floor plan from scratch: measure, draw, mark exits, check

Most evacuation map guides start with "get a floor plan of your building." If your church does not have one, this guide starts there.

No plan of the building? Start here.

Plenty of churches have no usable floor plan. The blueprints went with the builder decades ago, or the copy in the office drawer shows a wall that came down in the last renovation. Evacuation map tools and templates all assume you already have the plan, so the hard part is the part they skip.

This guide covers the whole job: measure the building (or scan it), draw it to scale, mark exits, routes and safety equipment, then check the plan against the building for the two mistakes that make an evacuation map wrong: doors that lead to rooms you never drew, and outside doors with no exit marked.

1. Decide what the plan is for

An evacuation floor plan has one job: get people out of the building. That decides what goes on it and what stays off.

  • One plan per floor. A basement, the ground floor and an upper floor each get their own. A sanctuary balcony counts as a floor if people sit in it.
  • Walls, doors, windows and stairs only. Show outside walls, inside walls, every door and which way it swings, windows, stairs, ramps and elevators.
  • No furniture. Tables, chairs and pianos move, and they clutter the map. Pews are the exception: if the sanctuary aisles are part of a route, draw the aisles as clear paths between blocks of pews.

Also list where each copy will hang: the sanctuary doors, the fellowship hall, the nursery and children's rooms, classrooms, the kitchen and the office hallway are the usual places. You will draw the base plan once and make one version of it for each of those places.

2. Get the base plan

The base plan is the floor drawn to scale with nothing marked on it yet. There are two ways to get one: measure it by hand, or scan it.

Option A: tape measure and graph paper

You need a 25 foot (or 8 metre) tape measure or a laser distance measurer, graph paper, a pencil, a clipboard and a helper to hold the other end of the tape. A small church floor takes an afternoon.

  1. Sketch first, measure second. Walk the floor and draw a rough sketch of every space in order: rooms, closets, hallways, restrooms, stair landings. It does not need to be to scale. Number each space.
  2. Measure each room wall by wall. Start at the door and go clockwise, writing each wall's length on the sketch. For doors and windows, write the distance from the nearest corner to the edge of the opening, then the opening's width.
  3. Note which way every door swings, and whether it locks.
  4. Measure wall thickness at a doorway (the depth of the frame). Leave walls out and the rooms add up shorter than the building.
  5. Check that rooms are square. Measure both diagonals of a rectangular room. If they match, the room is square. If they don't, note which corner is off.
  6. Check against the outside. Measure one long outside wall from outside the building. Add up the rooms along it plus the wall thicknesses. If the totals differ by more than a foot, measure that row of rooms again before you draw.

Pick a scale before you draw. For a whole floor, use 1:100 (1 cm on paper for 1 m of building) or 1/8 inch to the foot. For a small floor or one wing, use 1:50 or 1/4 inch to the foot. Check it fits first: a building 100 feet long is 12.5 inches on paper at 1/8 inch to the foot, which fits on 11 by 17 inch paper but not on letter paper. On graph paper with 4 squares to the inch, each square is one foot at 1/4 inch to the foot.

Then draw, in this order:

  1. Outside walls, as double lines the thickness of the wall.
  2. Inside walls.
  3. Doors, as a gap in the wall with a quarter circle showing the swing.
  4. Windows, as thin lines across the wall.
  5. Stairs, as parallel lines with an arrow pointing up and the word UP.
  6. Room names as people say them, like "Fellowship hall" or "Nursery".
  7. A north arrow and a scale bar. A scale bar stays right when the plan is copied larger or smaller; a written "1:100" does not.

Once the paper plan is right, it is worth tracing it into a drawing program so it can be updated when a room changes. Either way, the measuring is most of the work.

Option B: scan it with an iPhone

An iPhone with LiDAR (iPhone 12 Pro or a newer Pro or Pro Max) can measure rooms by scanning them. You walk each room with the phone and it builds the walls, doors and windows as you go.

Church Scan is an iPhone app we are building for this, for church buildings. You scan the building room by room and the app merges the rooms into floors. Large room mode traces big rooms like a sanctuary from the LiDAR mesh. Each room saves on the phone and scanning works offline, so a building can take several visits. You pin exits and safety equipment as you go, with notes and photos, and the app reads EXIT and safety-equipment signs in scan photos and suggests pins to keep, change or dismiss.

When the building is done, you upload it to Keyhall, which makes the floor plans and evacuation maps, or share it as a .churchscan file by AirDrop or Files. Church Scan is in development and not on the App Store yet. It needs iOS 17 or later. If you are weighing a general 3D scanner too, see how Church Scan compares with Polycam.

Whichever way you get it, check the base plan against the building before you mark anything on it. Stand in a room with the plan and look: are the doors and windows where the plan shows them?

3. Mark exits and routes

Mark every exit. That means every door to the outside that people can use in an emergency, including the ones staff forget: the side door by the platform, the kitchen's back door, the door at the top of the basement stairs. Use a green EXIT label or symbol and the same one every time.

Do not mark a door as an exit if it is locked from the inside, blocked, or opens into a fenced courtyard with no way out. If a door should be an exit but is chained shut or blocked by stacked chairs, fix the door, not the map.

Draw routes for each place a copy will hang.

  • A primary route: the shortest safe way from that spot to an exit, as solid arrows.
  • A backup route to a different exit, as dashed arrows, for when the first one is blocked.
  • Follow hallways and doorways. Never draw an arrow through a wall or through a room that is often locked, like the church office on a Sunday.
  • On upper floors and in the balcony, routes go to the stairs, never to an elevator.

Two rooms need extra thought in a church. In the sanctuary, a Sunday crowd leaves the way it came in, through the main doors, so the side exits need to be marked clearly. In the nursery and children's rooms, plan the routes with the people who run those rooms: they move many small children at once, and the nearest exit may be better for them than the main one.

4. Mark safety equipment and the assembly point

Mark where people can find:

  • Fire extinguishers
  • Fire alarm pull stations
  • AEDs (defibrillators)
  • First aid kits

Staff may also want the electrical panel, the gas shutoff and the water shutoff. Put those on a staff copy if they would clutter the posted maps. Use one symbol and one color for each kind of equipment, everywhere, and put each in the legend.

Choose an assembly point: a named place outside where everyone gathers and gets counted, such as "the far end of the north parking lot" or "the playground fence". Pick somewhere well away from the building and clear of where fire trucks will park; a common rule of thumb is at least 50 feet from the building. If the children's team reunites children with parents there, say so on the nursery's map.

5. Add a legend and "You are here"

The legend explains every symbol and line on the map, and nothing else. Around it, add the building's name, the floor, a north arrow, the scale bar and the date the map was drawn.

Each posted copy gets a "You are here" marker where it hangs, and its routes start from that marker. Make the base map once, then a version for each place it hangs.

Turn each copy to match the reader. The direction someone faces when reading the map should be up on the paper. A map that is correct but sideways for the person reading it slows them down when it matters.

Post each copy near the room's main door, at eye level; guides commonly suggest about 48 to 60 inches from the floor. Large room names help people read it from a step back.

The You are here marker is in the nursery. The primary route runs out of the nursery door, west along the hall, through the foyer and out the main entrance to the assembly point on the north lawn. The backup route runs through the nursery's second door into the fellowship hall and out its rear exit. Exits, fire extinguishers, pull stations, an AED and a first aid kit are marked, with a legend, a north arrow and a 20 foot scale bar. Ground floor, example church Sanctuary Fellowship hall Nursery Restrooms Hall Foyer Office Kitchen E E E F F F P P P A + AP Assembly point: north lawn Legend Primary route Backup route EExit FFire extinguisher PFire alarm pull station AAED +First aid kit You are here APAssembly point 020 ft N
An example for the copy posted in the nursery: a primary route out the main entrance, a backup route through the fellowship hall, every exit and piece of equipment, the assembly point, a legend, a north arrow and a scale bar.

6. Check the plan against the building

Before you print anything, walk the building once more with the plan and a pen. This catches the mistakes that are easy to make on paper and dangerous on the wall. Two are common.

  • Doors that lead to rooms you never drew. A door in the fellowship hall opens into a storage room you skipped, or a closet turns out to be a passage to the kitchen. If people can be in that space, draw it and give it a route. If it is a closet, draw it as one so nobody routes through it.
  • Outside doors with no exit marked. You drew the door but never marked it as an exit. Either it is an exit, so mark it and use it in the routes, or it can't be used, so find out why and fix it if it should be.

The way to find both: in each room, open every door and tick it on the plan once you know where it leads. At the end, any door without a tick is a question to answer. While you walk, also check that:

  • every room on the plan has a route out;
  • rooms that hold many people, like the sanctuary and the fellowship hall, have at least two ways out;
  • no route passes through a room that is often locked;
  • the routes you drew are the ones you would actually walk.
The same ground floor. Problem 1, at the east wall of the restrooms: a door leads into a storage room that was never drawn, shown as a dashed outline with a question mark. Problem 2, on the south wall of the office: an outside door with no exit marked. Both doors are circled in amber. Ground floor, before the floor check ? Sanctuary Fellowship hall Nursery Restrooms Hall Foyer Office Kitchen E E E 1 2 To fix 1 Door to a roomnot on the plan 2 Outside door,no exit marked
The same floor before the check. Door 1 leads into a storage room nobody drew. Door 2 is an outside door from the office with no exit marked. Both have to be answered before the map is printed.

Church Scan does this check for you

Before each upload, Church Scan's floor check flags doors that lead to rooms you have not scanned and suggests which doors are outside doors. It flags outside doors with no exit pin, with a one-tap fix to pin an exit there. You can dismiss a door you know is fine, and a reminder shows before you upload.

7. Review it with your fire marshal

An evacuation floor plan you draw yourself is guidance for your church, with no certification or code check behind it. What has to be posted, and where, depends on where you are. Take your plan to your local fire marshal or fire department and ask them to review it; many will walk the building with you if you ask.

In the United States, OSHA's rule on emergency action plans (29 CFR 1910.38) applies to employers, and NFPA 101, the Life Safety Code, covers the ways out of a building. Your fire marshal will know which apply to your church.

Then use the map. Walk the routes with your ushers, greeters and children's team, and use the free safety team walkthrough checklist to check exits, extinguishers and AEDs room by room. Redraw it when a renovation moves a door or a room changes use, and put the date on every copy so you can tell an old one from a new one.

Questions

Can I make an evacuation floor plan without the building's blueprints?

Yes. Measure each room with a tape measure or laser measurer, draw the floor to scale on graph paper, then mark the exits, routes and safety equipment. A LiDAR iPhone can do the measuring for you by scanning room by room.

What scale should an evacuation floor plan be?

Use 1:100 (1 cm on paper for 1 m) or 1/8 inch to the foot for a whole floor, and 1:50 or 1/4 inch to the foot for a small floor or one wing. Add a scale bar, so the plan stays readable when it is copied at another size.

What has to be on an evacuation map?

Every exit, a primary and a backup route from where the map hangs, a "You are here" marker, fire extinguishers, fire alarm pull stations, AEDs and first aid kits, the assembly point outside, a legend, a north arrow and the date it was drawn. Your local fire marshal can tell you what your area requires.

Do I need a separate evacuation plan for each floor?

Yes. Draw one plan per floor, including a basement and a sanctuary balcony if people use them, and show the stairs that lead down and out.

Can I scan the building with an iPhone instead of measuring it?

An iPhone with LiDAR (iPhone 12 Pro or a newer Pro model) can measure rooms by scanning them. Church Scan is an iPhone app for this, built for churches: it scans room by room, merges the rooms into floors and checks each floor for doors that lead nowhere. It is in development and not on the App Store yet.

Does the fire marshal have to approve our evacuation map?

It depends on where you are. A plan you draw yourself is guidance, not a certified plan or a code check. Ask your local fire marshal or fire department to review it.